Quick Answer
An IP44 socket is a socket rated to keep out solid objects larger than 1.0 mm and water splashed against it from any direction. An IP67 socket adds 30 minutes of temporary immersion at 1 m depth. Each rating is tested in one defined condition, so IP44 will not survive a hose jet and IP67 will not survive a pressure washer.
This guide compares what each digit actually proves, how the mated pair changes the answer, and where each rating belongs on a working site.
What Do the Two Digits in IP44 and IP67 Measure?
An IP code is a two-digit ingress protection rating published in IEC 60529, the international standard for enclosure sealing. The first digit covers solid objects, from a fingertip to fine dust. The second digit covers water, from vertical drips to high-pressure jets. Each digit is tested separately, on a defined sample, in a defined state.
On an industrial socket the code describes the product, not the installation. It says nothing about the cable, the gland, the panel cutout or the way the socket was mounted. Those parts decide whether the rating is still true after the first winter outdoors.
What the First Digit Covers for a Socket
Level 4 is the usual baseline for indoor industrial sockets. A 1.0 mm diameter probe pushed with 1 N of force must not reach live parts, and the enclosure must stop solid objects of 1.0 mm and above. Level 5 adds dust protection with limited ingress, and level 6 is dust tight. Most splash-proof sockets stop at 4, while watertight versions usually reach 6.
What the Second Digit Covers for Water
The water digits step up through different test rigs. Splash, jet and immersion are not variations of one test; they load the seal from different directions, at different pressures and for different times. A socket that passes a splash test can still take water the moment someone rests a hose against the lid.
| Water digit | Test condition | Where it usually belongs |
|---|---|---|
| IPX4 | Splashing water from any direction, 10 min at roughly 10 L/min | Covered workshop, plant room, under a canopy |
| IPX5 | 6.3 mm nozzle, 12.5 L/min at 30 kPa, 3 min from about 3 m | Open loading bay, edge of a wash area |
| IPX6 | 12.5 mm nozzle, 100 L/min at 100 kPa, 3 min from about 3 m | Deck wash, jet cleaning a few metres away |
| IPX7 | Temporary immersion, 30 min with the lowest point 1 m under water | Open yard socket, pit, slab that can flood |
| IPX9K | 80 °C water at 80 to 100 bar, 14 to 16 L/min, four angles | Food and beverage washdown zones |
Where Does IP44 Stop Working?
An IP44 socket handles rain, a mop splash and condensation running down a wall. It stops working when water arrives with speed. A garden hose at close range already delivers something closer to the IPX5 jet than to the IPX4 splash, and a washdown lance is two digits further away again.
Driving rain on an exposed wall is the other weak case. The test sprays from any direction for 10 minutes, but it does not reproduce wind pushing water into a lid lip for a full season. Sites that leave sockets facing the weather usually move those positions to IP67 even when the covered positions stay at IP44.
What Does an IP67 Socket Actually Survive?
IP67 makes two claims at once: dust tight at digit 6, and 30 minutes of immersion at digit 7. The immersion test puts the lowest point of the sample 1 m below the surface for 30 minutes, with no spraying and no pressure applied. Water may enter, provided it does not reach a harmful quantity or affect operation.
What the Immersion Test Does Not Cover
It does not cover 3 m, 8 hours, or water arriving at 80 bar. Continuous immersion is IP68, where depth and duration are agreed between buyer and maker rather than fixed by the standard. High-pressure cleaning is IP69K. An IP67 socket standing in a flooded pit for a week has left its test envelope, even though the label still reads IP67.
Does the Rating Apply to the Socket, the Plug or the Pair?
This is the most common source of field failures. A manufacturer tests and publishes a rating for one defined condition, and for a panel socket that condition is often the closed lid. For a plug and socket together it is the mated pair, and usually the pair from the same series.
IEC 60309-1 splits industrial plugs and sockets into splash-proof types, rated IP44, and watertight types, rated IP67. A watertight socket with a splash-proof plug in it is a compromise, not a rated assembly. Match both halves, and read the datasheet for the exact state that was tested.
The unmated state is the weak point. An IP67 socket with the lid hanging open is a funnel, and a spring that has lost tension defeats the seal without leaving a mark. This is why tethered lids and spare gaskets belong on the maintenance list, not in a drawer.
Which Rating Fits Which Location?
Most sites do not need one rating everywhere. The differences are modest per unit and significant per installation, so the practical method is to grade the location and match the socket to it. The table below is a starting point, not a substitute for the project specification.
| Location | Minimum rating | Reason |
|---|---|---|
| Indoor workshop, dry floor | IP44 | Splash only; quick service access matters |
| Covered yard, canopy edge | IP44 to IP65 | Wind-driven rain reaches the lid |
| Open yard, no shelter | IP67 | Standing water and pooled rain |
| Washdown bay, food line | IP67, with IP69K where jets are aimed | Pressure and temperature, not volume |
| Construction site distribution | IP44 minimum, IP67 at ground level | IEC 60364-7-704 treats these as a special case |
Construction and demolition sites deserve a separate note. IEC 60364-7-704 handles socket outlets on such sites as a special case and commonly sets IP44 as the floor for the assembly. Units that sit on the ground or in a puddle are still better served by a watertight version, because the rating was never meant to survive standing water.
Why Do Sealed Sockets Still Fill With Water?
Water inside a sealed enclosure rarely comes past the gasket. It usually travels down the cable, through a gland that does not match the jacket, or condenses out of the air pocket when the temperature drops overnight.
What Cable Entry Does to the Rating
A socket is rated with its own entry, and once a gland is fitted the assembly inherits the gland's seal and the installer's torque. A jacket diameter outside the clamping range leaves a path along the sheath, and water follows it by capillary action into the terminal chamber. Measure the jacket rather than the conductor, and check the gland range before ordering.
Why Condensation Forms Inside a Sealed Socket
A sealed enclosure that warms by day and cools at night pulls moisture out of the cable and the trapped air. No IP rating addresses that. A drain point, a breather membrane or a desiccant does, and the same failure path is covered in our review of the common causes of industrial connector failure in harsh environments.
What Do You Lose by Specifying IP67 Everywhere?
Watertight construction is not free. Gaskets, tighter tolerances, heavier lids and higher insertion force all add cost and time, and every service visit ends with a lid that has to be re-seated correctly. A torn gasket turns an IP67 socket into an unrated one with no visible warning.
There are practical losses too:
- Sealed sockets hold moisture in as effectively as they keep it out, so a wet assembly stays wet.
- Usable cable range narrows as the entry gets tighter.
- Inspection takes longer, because the state of the seal is hidden under the lid.
- Every service visit ends with a lid that must be re-seated, and a torn gasket is invisible.
Where a location is genuinely dry, an IP44 socket is easier to live with, and the budget is better spent on the positions that face water. The same logic applies to the plug on the cable: a watertight plug on a splash-proof cordset does not raise the rating of either part.
How Should the IP Requirement Be Written on a Drawing?
Two digits on a drawing are ambiguous. They say nothing about the state tested, the standard applied, or the cable entry the socket must accept. A supplier can meet that line item exactly and still deliver something that fails in service, so the requirement needs the surrounding conditions attached.
The IP Rating Requirement Checklist
- Rating and standard: state IP44 or IP67 to IEC 60529, not the digits alone.
- Tested state: closed lid, mated pair, or unmated with the cap fitted.
- Cable entry: gland type and thread, plus the jacket diameter range the socket must accept.
- Environment beyond water: UV exposure, salt spray, wash chemicals and ambient temperature.
- Evidence: the test report, or at minimum the state and duration that were tested.
- Service items: tethered lid, spare gaskets and expected mating cycles per shift.
Housing material belongs on the same list. A polyamide that absorbs water or ages under UV will loosen its grip on the gasket long before the contacts wear, which is why material choice decides long-term reliability as much as the rating does.
Which Evidence Should a Supplier Provide?
Ask for the test state before the test number. A report that shows IP67 on a closed lid tells you the gasket works; it does not tell you the socket stays sealed with a plug inserted in the rain. Ask which sample was tested, whether it was mated, and how long the sample had been in service before the test.
For the wider picture, our guide to how IP67, IP68 and IP69K affect application selection covers the upper end of the scale, and the comparison of IP65 to IP69K housings shows what changes inside a product when the second digit rises.
WEIPU has manufactured circular and industrial connectors since 1996, and the TYP range carries the same IEC 60309 pin configurations in splash-proof and watertight builds. Treat the catalogue as an evaluation starting point: verify the part number, the tested state behind the rating, and the gland range against the current datasheet before the socket goes on a drawing.
Conclusion
IP44 and IP67 answer different questions. IP44 says the socket tolerates splashing from any direction; IP67 says it tolerates 30 minutes under 1 m of still water. Neither says anything about jets, cable entries, condensation or the state of the lid. Grade the site, write the tested condition on the drawing, match plug to socket, and measure the cable before choosing the gland. Then check the report rather than the two digits.
Related Products for Outdoor and Washdown Sockets
The TYP range splits the same IEC 60309 pin configurations into splash-proof IP44 and watertight IP67 builds, so a site can be graded without changing the plug convention between areas. The four parts below cover the two most common split points: plugs on the cable side, and panel sockets where the water actually arrives.
- The 16 A 3-pin IP44 cable plug by TYP231 is the splash-proof half for covered bays and indoor distribution.
- The 16 A 3-pin IP67 cable plug by TYPR171 adds a sealed shell and cap for open yards and wet slabs.
- The 32 A 3-pin IP44 angled panel socket by TYP3801 suits panel edges that see splashes but never jets.
- The 63 A 5-pin IP67 angled panel socket by TYP3924 covers three-phase positions exposed to standing water.
Each part exists in several current ratings and pin counts, so confirm the contact layout and the tested state of the rating against the datasheet before ordering. The full range of IP44 and IP67 plugs and sockets, with the tested state written on each datasheet, is listed on the TYP IEC 60309 connector page.
Discuss Your IP44 Socket Requirements
Send the working conditions and we will reply with specific part numbers plus the evidence behind each rating, rather than a generic catalogue page. The more of the following you can supply, the shorter the review loop:
- Installation: indoor, covered or exposed; panel position and mounting height.
- Cable: jacket outer diameter, conductor cross-section, and whether a gland is already specified.
- Electrical: current, voltage, pin count, and any three-phase or neutral requirement.
- Environment: target IP rating, cleaning method and pressure, UV, salt and ambient temperature.
For drawings, samples or a rating review, contact the WEIPU engineering team and describe the socket position you are working on.
![Cargo UAV Autonomy and Flight AI — Ch.06: Route Planning and Airspace Integration [EN]](https://media2.dev.to/dynamic/image/width=800%2Cheight=%2Cfit=scale-down%2Cgravity=auto%2Cformat=auto/https%3A%2F%2Fdev-to-uploads.s3.us-east-2.amazonaws.com%2Fuploads%2Farticles%2F54s7rrr8fw0ipjpci49u.png)
![Cargo UAV Autonomy and Flight AI — Ch.05: Perception and Sensor Fusion for UAV [EN]](https://media2.dev.to/dynamic/image/width=800%2Cheight=%2Cfit=scale-down%2Cgravity=auto%2Cformat=auto/https%3A%2F%2Fdev-to-uploads.s3.us-east-2.amazonaws.com%2Fuploads%2Farticles%2Faemm4fj7d911fwx0irut.png)
![Cargo UAV Autonomy and Flight AI — Ch.04: Autonomous Navigation for UAV [EN]](https://media2.dev.to/dynamic/image/width=800%2Cheight=%2Cfit=scale-down%2Cgravity=auto%2Cformat=auto/https%3A%2F%2Fdev-to-uploads.s3.us-east-2.amazonaws.com%2Fuploads%2Farticles%2F98idhn116ojz4pviet9j.png)
![Cargo UAV Autonomy and Flight AI — Ch.03: Flight Control Software [EN]](https://media2.dev.to/dynamic/image/width=800%2Cheight=%2Cfit=scale-down%2Cgravity=auto%2Cformat=auto/https%3A%2F%2Fdev-to-uploads.s3.us-east-2.amazonaws.com%2Fuploads%2Farticles%2Fminle8x2lymdhmeo5fbt.png)
![Cargo UAV Autonomy and Flight AI — Ch.02: UAV System Architecture [EN]](https://media2.dev.to/dynamic/image/width=800%2Cheight=%2Cfit=scale-down%2Cgravity=auto%2Cformat=auto/https%3A%2F%2Fdev-to-uploads.s3.us-east-2.amazonaws.com%2Fuploads%2Farticles%2F2w7u1ajhaoa23mrl0dqs.png)